webassets/HPIM3768a.JPG

webassets/HPIM3767a.JPG

webassets/HPIM3764a.JPG

webassets/DSCF4586.JPG

webassets/65superclean099.jpg

webassets/65superclean153.jpg

webassets/DSCF4588.JPG

webassets/65superclean144.jpg

webassets/DSCF4587.JPG

webassets/65superclean126.jpg

webassets/DSCF4589.JPG

webassets/65superclean117.jpg

webassets/65floorpanlancesvert006.jpg

webassets/65floorpanlancesvert004.jpg

webassets/vertprimer016.jpg

webassets/65floorpanlancesvert005.jpg

webassets/65floorpanlancesvert003.jpg

webassets/vertprimer015.jpg

webassets/vertprimer007.jpg

webassets/vertprimer009.jpg

webassets/vertprimer006.jpg


Here are two projects were as you will see had some serious rust issues, the 70 convertible had  bondo  on lower 8-12" of both sides had been shaped and filled with spray foam, both sides were removed all metal prepped and cleaned and new replacement panels welded in.

sheetmetal and welding work performed by Rodney Culp for PierceAutomotive.

1963 sedan
this car was completely rotten on right side
heater channel,rear quarter,front quarter,
hinge, inside rear heater inlet area.had been
sitting on flats for 15+ years, car mostly original
when found.also replaced inside left frt heater
channel section.

webassets/HPIM4955.JPG

webassets/HPIM4956.JPG

webassets/HPIM3763a.JPG

webassets/HPIM4965.JPG

webassets/HPIM3762a.JPG

webassets/bluecar005.jpg

webassets/bluecar012.jpg

webassets/bluecar009.jpg

sealer is on ready for final touch before paint goes on.

webassets/65floorpanlancesvert001.jpg

webassets/sodablast70vert013.jpg

1970 CONVERTIBLE
SUPPORT RAILS,HEATER CHANNELS,REAR & FRT QUARTER SECTIONS,HINGE POST ARE ALL
ROTTEN.

webassets/bodywork001.jpg

webassets/bodywork006.jpg

webassets/sodablast70vert008.jpg

filling gas lid hole, hand working section, this area was crushed in a past life filled with 1/2 inch of bondo

webassets/65superclean090.jpg

here is after sheet metal repairs, seam sealed,primed and undercoated, next fitting and aligning doors.

webassets/sodablast70vert010.jpg

smoothing panels out, doors are finally lined and fitted, getting close to paint

webassets/sodablast70vert009.jpg

here front of car was crushed in past life, filled with bondo, here we are hand working sheet metal to help reduce the amount of filler needed to finish.

webassets/lancescar.jpg

photo here is before work in photos began
below shaving exhaust tips


webassets/newpics21210098jpg.jpg

webassets/newpics21210102jpg.jpg

webassets/newpics21210090jpg.jpg

webassets/newpics21210089jpg.jpg

webassets/newpics21210083jpg.jpg

webassets/newpics21210100jpg.jpg

webassets/paintedvert069jpg.jpg

webassets/newpics21210099jpg.jpg

webassets/paintedvert070jpg.jpg

webassets/paintedvert068jpg.jpg

webassets/HPIM4960.JPG

webassets/HPIM4959.JPG

webassets/HPIM3761a.JPG

webassets/HPIM3760a.JPG

webassets/HPIM4961.JPG

webassets/HPIM4962.JPG

webassets/65superclean162.jpg

all fender wells and support rails seam sealed, prepped and primed then undercoated with rock guard material

webassets/vertprimer007.jpg

webassets/DSCF4585.JPG

webassets/1970vertlancescar084.jpg

1970 CONVERTIBLE

webassets/65superclean082.jpg

webassets/1970vertlancescar013.jpg

webassets/1970vertlancescar077.jpg

webassets/1970vertlancescar024.jpg

webassets/1970vertlancescar055.jpg

webassets/1970vertlancescar097.jpg

webassets/1970vertlancescar087.jpg

webassets/65superclean135.jpg

webassets/65superclean108.jpg